Blind-Hole Thread Inserts for Robot Actuator Housings

By Jay Zhou | Yueyi

To prevent a cover screw from bottoming in a robot actuator housing, compare the longest screw and thinnest cover stack with the minimum usable insertion depth. Check engagement separately using the shortest screw and thickest stack. For a wire thread insert, gauge the parent thread before installation, then check insert depth and verify that the production screw seats the cover.

Why the torque wrench can click before the cover is clamped

Consider a CNC-machined aluminum actuator housing with a removable service cover. The drawing calls for a wire insert in a blind boss. If the screw tip hits the hole bottom, an unremoved tang or incomplete threads before the head seats, the tool can reach its torque setting while the cover is still loose. NASA-STD-5020B documents the same interference mechanism for blind-hole fasteners in its own field. The actuator drawing governs this joint.

For a conventional screw that seats under its head, subtract the seated cover-and-washer stack from the screw’s under-head length to find how far it protrudes into the housing. For example, a 14.0 mm maximum screw length and a 3.2 mm minimum stack give 10.8 mm of protrusion. If the minimum permitted insertion is 10.5 mm, the screw exceeds that limit by 0.3 mm. These numbers illustrate the comparison. On a real drawing, apply the required clearance and check engagement after any change to screw length.

Head seatedTip bottomedTip clearanceHead gapContactSection views · schematic, not to scale
Figure 1. Original engineering schematic. A bottomed tip can leave a gap below the screw head. The dashed lines represent the insert in section.

Machine the boss for the specified insert system

Keep drilled depth, full parent-thread depth, insert setback and maximum screw penetration separate on the drawing. A drill point and a tap lead consume depth. The parent thread is the larger thread that holds the insert, often called an STI (screw thread insert) thread. Use the approved insert system’s drill and tap data for the exact part number. Check the remaining wall to the actuator cavity and tool clearance before committing to the hole depth.

CNC spindle above a clamped metal workpiece with a machined circular opening
Figure 2. CNC machining image from Yueyi’s robotics page, shown as a workholding example.
OptionWhen to use itConfirm before release
Direct aluminum threadThe drawing permits it and the joint has been validated for its load and service cycles.Full-thread depth, fit, engagement and clearance at the screw tip.
Tanged wire insertThe drawing calls for the insert and the installation plan controls the tang.STI gauge, installed setback, tang removal and retrieval when required.
Tangless wire insertThe drawing approves it and access makes tang retrieval difficult.Approved insert and driver, STI gauge, installed setback and screw engagement.

Inspect before and after installing the insert

Before insertion, check the minor diameter with the specified plain gauge and the parent thread with the correct STI GO and NO-GO gauge. Verify the usable full-thread depth separately using an agreed method. If a finish affects the parent thread, gauge in the specified condition before insertion. KATO’s installation guide explains these checks and why a standard plug gauge can give a misleading result after installation, especially with a locking insert.

After insertion, verify the top coil setback from the seating face and look for damage or a displaced coil with suitable magnification. Follow the approved system’s rules for tang handling. Böllhoff’s metric HELICOIL Plus guide illustrates how a retained tang can limit penetration in some blind-hole configurations. On the first article, use the actual cover, washer and screw or an approved equivalent, and check that the cover seats before final tightening. Record clearance, engagement and seating alongside the dimensional inspection results.

What to send for a machining quote

Send the housing drawing and STEP file, the cover stack and screw drawing, the approved insert part number and length, boss wall limits, finish and masking notes, and the required engagement and tip clearance. Specify the assembly check, inspection records and quantities. See Yueyi’s CNC machining services or send the drawings for review.

Frequently asked questions

Does a passing STI gauge prove that the cover will seat?

It checks the parent thread. Verify the screw and cover stack against the available insertion depth and confirm seating on the assembly.

Can I solve bottoming by choosing a shorter screw?

Yes, if the shortest allowed screw still provides the specified full-thread engagement with the thickest permitted stack.

Should the top coil sit flush with the housing?

Use the setback required by the drawing and the approved insert system. Measure it from the specified seating face.

Content Summary

Contact Us

Are you ready for production? Submit your documents and we will deliver the parts.

Over 13 years of manufacturing experience, serving 1,500+ customers and delivering 10 million parts.

Contact Us